| FOX Rx AV |
| NOTE | The FOX Rx AV is a receiver with one or two fiber optic cables linking it to a transmitter. |
|
| NOTE | The analog video input signal is digitized pixel for pixel in the transmitter, sent digitally through the fiber cable, and converted back to analog video in the receiver. |
|
| NOTE | The analog audio signals are digitized in the transmitter, sent through the fiber cable, and converted back to analog audio in the receiver. |
|
| NOTE | The FOX Rx AV receiver is a class 1 laser product. It meets the safety regulations of IEC-60825. |
|
|
| Optical fiber interconnection between transmitter and receiver |
|---|
| Number/type | 1 or 2 fiber optic |
| NOTE | Only one fiber is required to transmit video, audio, and unidirectional data. A second fiber is required to transmit return data for bidirectional control and communication. |
|
| Connectors | 2 LC connectors |
| Operating distance | |
| Singlemode | 30 km (18.75 miles) with singlemode (SM) cables with a FOX Rx AV SM |
| Multimode | 500 m (1640') with 62.5 µm multimode (MM) cables with a FOX Rx AV MM
1 km (3280') with 50 µm multimode cables with a FOX Rx AV MM
2 km (6561') with 50 µm, 2000 MHz bandwidth laser optimized multimode cables with a FOX Rx AV MM |
| NOTE | Operating distance is approximate. These are typical maximum distances that may vary depending on factors such as fiber type, fiber bandwidth, connector splicing, losses, modal or chromatic dispersion, environmental factors, and kinks. |
|
| Nominal peak wavelength | 850 nm for FOX Rx AV MM, 1310 nm for FOX Rx AV SM |
| Data rate | 2.125 Gbps |
| Transmission power | |
| Singlemode | -5 dBm, typical |
| Multimode | -5 dBm, typical |
| Maximum receiver sensitivity | |
| Singlemode | -18 dBm, typical |
| Multimode | -12 dBm, typical |
| Optical loss budget | |
| Singlemode | 13 dB, maximum |
| Multimode | 7 dB, maximum |
|
| Video |
|---|
| Gain | Unity |
| Standards | |
| Input | NTSC 3.58, NTSC 4.43, PAL, SECAM, autodetected |
| Output | NTSC 3.58, PAL (follows vertical rate) |
| Decoder type | Adaptive 2D, digital comb filter |
|
| Video output |
|---|
| Number/signal type | 1 component (Y, R-Y, B-Y) video, S-video, composite video |
| Connectors | 1 x 3 female BNC or 1 female 4-pin mini DIN for S-video |
| Nominal level | 1.0 Vp-p for Y of component video and S-video, and for composite video
0.7 Vp-p for R-Y, B-Y of component video
0.3 Vp-p for C of S-video |
| Minimum/maximum levels | 0.3 V to 1.5 Vp-p |
| Impedance | 75 ohms @ 5 MHz |
| Return loss | <-40 dB @ 5 MHz |
| DC offset | +350 mV, maximum, with input at 0 offset |
| Video delay | 1-2 frames |
|
| Audio |
|---|
| Gain | |
| Range | Adjustable, -18 dB to +10 dB |
| Default | Unbalanced output: -6 dB; balanced output: 0 dB |
| Frequency response | 20 Hz to 20 kHz, ±0.5 dB |
| THD + Noise | 0.15% @ 1 kHz at nominal level |
| S/N | >80 dB at maximum output (unweighted) |
| CMRR | 65 dB @ 20 Hz to 20 kHz |
| Audio bits per sample | 18 bits per channel, 2 channels (L, R) |
| Sampling rate | 48 kHz |
|
| Audio output |
|---|
| Number/signal type | 1 stereo, balanced/unbalanced or
2 mono, balanced/unbalanced |
| Connectors | (1) 3.5 mm captive screw connector, 5 pole |
| Impedance | 50 ohms unbalanced, 100 ohms balanced |
| Nominal level | +4 dBu (1.23 Vrms), -10 dBV (316 mVrms) |
| Maximum level (Hi-Z) | >+19 dBu, unbalanced at 1% THD+N |
| Maximum level (600 ohm) | >+15 dBm, unbalanced at 1% THD+N |
| Audio delay | 1.5 frames |
|
| Control/remote |
|---|
| Serial control ports |
| Control | 1 RS-232, 3.5 mm captive screw connector, 5 pole (3 pins are used) (rear panel); in parallel with front panel jack
1 RS-232, 2.5 mm mini stereo jack (front panel) |
| Pass-through | 1 RS-232, 3.5 mm captive screw connector, 5 pole (3 pins are used) (rear panel) |
| Baud rate and protocol | |
| Control | 9600 baud, 8 data bits, 1 stop bit, no parity |
| Pass-through | 9600 to 115200 baud |
| Serial control pin configurations |
| Pass-through | Captive screw connector: 1 = Tx, 2 = Rx, 3 = GND |
| Control | Captive screw connector: 3 = GND, 4 = Tx, 5 = Rx
Mini stereo jack: tip = Tx, ring = Rx, sleeve = GND |
| Program control | Extron control/configuration program for Windows®
Extron Simple Instruction Set (SIS™) |
|
| General |
|---|
| Power supply | External
Input: 100-240 VAC, 50-60 Hz
Output: 12 VDC, 1.5 A, 18 watts |
| Power input requirements | 12 VDC, 0.6 A |
| Ambient temperature/humidity | Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing |
| Cooling | Convection, vents on left side and top |
| Mounting | |
| Rack mount | Yes, with optional rack shelf kit |
| Furniture mount | Yes, with optional under-desk mounting kit |
| Enclosure type | Metal |
| Enclosure dimensions | 1.7" H x 4.3" W x 6.0" D (1U high, quarter rack wide)
(4.3 cm H x 10.9 cm W x 15.2 cm D)
(Depth excludes connectors.) |
| Product weight | 0.8 lbs (0.4 kg) per unit, 1.6 lbs (0.7 kg) per pair |
| Regulatory compliance | CE, c-UL UL, CE**, C-tick, FCC Class A**, ICES, VCCI,
Complies with the appropriate requirements of RoHS, WEEE |
| Product warranty | 3 years parts and labor |
| Everlast power supply warranty | 7 years parts and labor |
| NOTE | All nominal levels are at ±10%. |
|
| NOTE | Specifications are subject to change without notice. |
|
| (4362-090418-D3) |