| MTP 4T 15HD RS |
|
| Video |
|---|
| Gain | Unity |
| Number/signal type | 4 sets of proprietary analog signals |
| Connectors | 4 female RJ-45 |
|
| Video input and loop through — per transmitter |
|---|
| Number/signal type | 1 analog RGBHV, RGBS, RGsB, RsGsBs, component video (with bi-level or tri-level sync), S-video, or composite video
1 buffered RGBHV, RGBS, RGsB, RsGsBs local monitor loop through (includes ID bits) |
| Connectors | 2 female 15-pin HD |
| Nominal level | 1 Vp-p for Y of component video and S-video, and for composite video
0.7 Vp-p for RGB and for R-Y and B-Y of component video
0.3 Vp-p for C of S-video |
| Minimum/maximum levels | 0.3 V to 1.45 Vp-p |
| Impedance | 75 ohms |
| Horizontal frequency | 15 kHz to 130 kHz |
| Vertical frequency | 30 Hz to 150 Hz |
| Return loss | <-30 dB @ 5 MHz |
| DC offset (max. allowable) | 250 mV |
|
| Video output — see receivers' specifications |
|---|
|
| Sync |
|---|
| Input type (transmitter) | RGBHV, RGBS, RGsB, RsGsBs, bi-level or tri-level for component video |
| Output type (receivers) | RGBHV, RGBS, RGsB, RsGsBs |
| Standards | NTSC 3.58, NTSC 4.43, PAL, SECAM |
| Input level (transmitter) | 3.5 V to 5.5 Vp-p, unterminated |
| Output level (receivers) | 4.0 V to 5.0 Vp-p, unterminated |
| Input impedance | 510 ohms |
| Output impedance | 110 ohms |
| Max. input voltage | 5.5 Vp-p |
| Polarity | Positive or negative |
|
| Control/remote — external device (pass-through, unidirectional or bidirectional) |
|---|
| Serial control port input/output | RS-232 via (1) 3.5 mm, 3 pole captive screw connector |
| Serial control port output/input | 1 set of proprietary signals on a female RJ-45 jack |
| NOTE | The serial communications link of an MTP RL 15HD RS or MTP RL 15 HD RS SEQ is unidirectional only, transmitter to receiver, unless the receiver's directional jumper has been repositioned. The jumper should be repositioned only when the receiver is the only one in the system. |
|
| Baud rates | Up to 38400 bps at up to 600' (183 m) (Higher data rates and distances are possible. Performance will vary based on baud rate and cable length.) |
| Protocol | Data bits = 5 - 8
Stop bits = 1 or 2
Parity = odd, even, none
Flow control = XON, XOFF, none |
| NOTE | Protocol is mirrored between the transmitter and the receiver. |
|
| Serial control pin configuration | Captive screw connectors: 1 = TX, 2 = RX, 3 = GND |
|
| General |
|---|
| Recommended cable type | CAT 5/5e/6 (shielded or unshielded) |
| Power | 100 VAC to 240 VAC, 50-60 Hz, 20 watts, internal |
| Ambient temperature/humidity | Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing |
| Cooling | Convection, no vents |
| Mounting | |
| Rack mount | Yes, with included mounting kit |
| Enclosure type | Metal |
| Enclosure dimensions | 1.7" H x 17.5" W x 8.5" D (1U high, full rack wide)
(4.3 cm H x 44.4 cm W x 21.6 cm D)
(Depth excludes connectors.) |
| Product weight | 6.0 lbs (2.7 kg) |
| Shipping weight | 10 lbs (5 kg) |
| Vibration | ISTA 1A in carton (International Safe Transit Association) |
| Regulatory compliance |
| Safety | CE, c-UL, UL |
| EMI/EMC | CE, C-tick, FCC Class A, ICES, VCCI |
| Product warranty | 3 years parts and labor |
| NOTE | All nominal levels are at ±10%. |
|
| NOTE | Specifications are subject to change without notice. |
|
| (7.6-111609-D6) |