| MTP AV Series |
|
| Video |
|---|
| Gain | Unity |
| Differential phase error | <1.0° at 3.58 MHz and 4.43 MHz |
| Differential gain error | <1.0% at 3.58 MHz and 4.43 MHz |
|
| Video input |
|---|
| Number/signal type | |
| MTP T CV/AV Series | 1 composite video |
| MTP T SV Series | 1 S-video |
| MTP R CV/AV/SV Series | 1 set of proprietary analog signals |
| Connectors | |
| MTP T CV/AV Series | 1 female BNC |
| MTP T AV AAP | 1 female RCA |
| MTP T SV Series | 1 female 4-pin mini DIN |
| MTP R CV/AV/SV Series | 1 female RJ-45 |
| Nominal level | 1 Vp-p for Y of S-video and for composite video
0.3 Vp-p for C of S-video |
| Minimum/maximum levels | 0.3 V to 1.5 Vp-p with no offset |
| Impedance | 75 ohms |
| Return loss | <-30 dB, DC @ 10 MHz |
| DC offset (max. allowable) | 100 mV |
|
| Video output |
|---|
| Number/signal type | |
| MTP T CV/AV/SV Series, MTP T AAP Series | 1 set of proprietary analog signals |
| MTP R CV/AV Series | 1 composite video |
| MTP R SV Series | 1 S-video |
| Connectors | |
| MTP T CV/AV/SV Series | 1 female RJ-45 |
| MTP T AAP Series | 1 female RJ-45 on a 3" (7.6 cm) pigtail |
| MTP R CV/AV Series | 1 female BNC |
| MTP R SV Series | 1 female 4-pin mini DIN |
| Nominal level | 1 V p-p for Y of S-video and for composite video
0.3 V p-p for C of S-video |
| Minimum/maximum levels | 0.3 V to 1.5 Vp-p |
| Impedance | 75 ohms |
| Return loss | <-35 dB @ 5 MHz |
| DC offset | ±20mV with input at 0 offset |
|
| Sync |
|---|
| Standards | NTSC 3.58, NTSC 4.43, PAL, SECAM |
|
| Audio — audio models (A, AV, SVA models) only |
|---|
| Gain | |
| RCA models | Unbalanced output: 0 dB (unity) |
| All other models | Unbalanced output: 0 dB (unity); balanced output: +6 dB |
| Frequency response | 20 Hz to 20 kHz, ±0.25 dB |
| THD + Noise | 0.03% @ 1 kHz, 0.3% @ 20 kHz at nominal level |
| S/N | |
| RCA models | >90 dB, at maximum output (unweighted) |
| All other models w/audio | >90 dB, balanced at maximum output (unweighted) |
| Crosstalk | <-80 dB @ 1 kHz, fully loaded |
| Stereo channel separation | >75 dB @ 1 kHz |
| CMRR | >34 dB @ 20 Hz to 20 kHz |
|
| Audio input — audio models (A, AV, SVA models) only |
|---|
| Number/signal type | |
| MTP T AV, MTP T SV A | 1 stereo, balanced/unbalanced |
| MTP T AV/SV A RCA, MTP T AAP, MTP T 45 Series | 1 stereo, unbalanced |
| MTP R Series | 1 set of proprietary analog signals |
| Connectors | |
| MTP T AV, MTP T SV A | (1) 3.5 mm captive screw connector, 5 pole |
| MTP T AV/SV A RCA, MTP T AAP | 1 pair of female RCA |
| MTP R Series | 1 female RJ-45 (shielded) |
| Impedance | >5.6k ohms ±5% unbalanced, >10k ohms ±5% balanced |
| Nominal level | -10 dBV (0.32 Vrms) |
| Maximum level | >+2.4 dBu (balanced or unbalanced) at 1%THD+N |
| NOTE | 0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu |
|
|
| Audio output — audio models (A, AV, SVA models) only |
|---|
| Number/signal type | |
| MTP T Series | 1 set of proprietary analog signals (all MTP T models) |
| MTP R AV, MTP R SV A | 1 stereo or dual mono, balanced/unbalanced |
| MTP R AV/SV A RCA | 1 stereo or dual mono, unbalanced |
| Connectors | |
| MTP T Series | 1 female RJ-45 (shielded) |
| MTP T AAP Series | 1 female RJ-45 on a 3" (7.6 cm) pigtail |
| MTP R AV, MTP R SV A | (1) 3.5 mm captive screw connector, 5 pole |
| MTP R AV/SV A RCA | 1 pair of female RCA |
| Impedance | |
| MTP R AV, MTP R SV A | 50 ohms unbalanced, 100 ohms balanced |
| MTP R AV/SV A RCA | 50 ohms unbalanced |
| Gain error | ±0.1 dB channel to channel |
| Maximum level (Hi-Z) | >+3.3 dBu, balanced or unbalanced at 1%THD+N |
| Maximum level (600 ohm) | >+2.0 dBm, balanced or unbalanced at 1%THD+N |
|
| General |
|---|
| Recommended cable type | CAT5/5e/6 (shielded or unshielded) |
| External power supply | 100 VAC to 240 VAC, 50-Hz, external; to 12 VDC, 1.0 A, regulated |
| Power input requirements | 12 VDC, 0.2 A |
| NOTE | If the distance between the transmitter and receiver is less than 500' (150 m) and if the internal jumper is in setting 2, you can connect a power supply to only one device in a transmitter/receiver pair. If the distance between transmitter and receiver is greater than 500' (150 m) or if the internal jumper is in setting 1 (default), connect a power supply to each device. |
|
| Temperature/humidity | Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing |
| Cooling | Convection, no vents |
| Mounting | |
| Rack mount | |
| MTP T AAP Series | Yes, with optional rack panel |
| All other models | Yes, with optional 1U rack shelf |
| Furniture or wall mount | |
| MTP T AAP Series | Yes, with optional AAP mounting plates |
| All other models | Yes, with optional brackets. |
| Enclosure type | Metal |
| Enclosure dimensions (Depths exclude connectors and cables.) |
| MTP T AAP Series | |
| Faceplate | 1.4" H x 3.5" W x 0.1" D (3.6 cm H x 8.9 cm W x 0.3 cm D) (double space AAP plate) |
| Transmitter | 1.35" H x 2.7" W x 1.3" D (3.4 cm H x 6.9 cm W x 3.3 cm D) |
| All other models | 1.7" H x 2.2" W x 3.0" D (1U high, one-eighth rack wide)
(4.2 cm H x 5.6 cm W x 7.6 cm D) |
| Product weight | 1.0 lbs (0.5 kg) |
| Shipping weight | 3 lbs (2 kg) |
| Vibration | ISTA 1A in carton (International Safe Transit Association) |
| Regulatory compliance | |
| Safety | CE, c-UL, UL |
| EMI/EMC | CE, C-tick, FCC Class A, ICES, VCCI |
| MTBF | 30,000 hours |
| Warranty | 3 years parts and labor |
| NOTE | All nominal levels are at ±10%. |
|
| NOTE | Specifications are subject to change without notice. |
|
| (7.6-113009-D21) |