| MTP 15HD A Series Combo |
|
| Video |
|---|
| Gain | Unity |
| Number/signal type | 1 set of proprietary analog signals |
| Connectors | |
| MTP R 15HD RSA D | 1 female RJ-45 on a pigtail |
| All other models | 1 female RJ-45 |
|
| Video input and loop through — transmitters |
|---|
| Number/signal type | |
| MTP T 15HD A, MTP C7 T 15HD A | 1 analog RGBHV, RGBS, RGsB, RsGsBs, component video, S-video, or composite video
1 buffered RGBHV, RGBS, RGsB, RsGsBs local monitor loop through (includes ID bits) |
| MTP T 15HD A AAP, MTP T 15HD A D, MTP T 15HD A WM | 1 analog RGBHV, RGBS, RGsB, RsGsBs, component video, S-video, or composite video |
| Connectors | |
| MTP T 15HD A, MTP C7 T 15HD A | 2 female 15-pin HD |
| All other transmitters | 1 female 15-pin HD |
| Nominal level | 1 Vp-p for Y of component video and
S-video, and for composite video
0.7 Vp-p for RGB and for R-Y and B-Y of component video
0.3 Vp-p for C of S-video |
| Minimum/maximum levels | 0.3 V to 1.45 Vp-p |
| Impedance | 75 ohms |
| Horizontal frequency | 15 kHz to 130 kHz |
| Vertical frequency | 30 Hz to 150 Hz |
| Return loss | <-30 dB @ 5 MHz |
| DC offset (max. allowable) | 250 mV |
|
| Video output — receivers (MTP RL 15HD A, MTP RL 15HD A SEQ, MTP R 15HD RSA D, MTP 1500RL 15HD A SEQ. MTP C7 RL 15HD A) |
|---|
| Number/signal type | |
| MTP R 15HD RSA D | 1 analog VGA-UXGA RGBHV, RGBS, RGsB, RsGsBs, HD component video, component video, S-video, or composite video |
| All other receivers | 1 set of proprietary analog signals
1 analog RGBHV, RGBS, RGsB, RsGsBs, component video (bi-/tri-level sync), S-video, or composite video |
| Connectors | |
| MTP R 15HD RSA D | 1 female 15-pin HD |
| All other receivers | 1 female RJ-45
1 female 15-pin HD |
| Nominal level | 1 Vp-p for Y of component video and S-video, and for composite video
0.7 Vp-p for RGB and for R-Y and B-Y of component video
0.3 Vp-p for C of S-video |
| Minimum/maximum levels | 0.3 V to 1.45 Vp-p |
| Impedance | 75 ohms |
| Return loss | <-30 dB @ 5 MHz |
| DC offset | |
| MTP R 15HD RSA D | <±20 mV with input at 0 offset |
| All other receivers | <±35 mV with input at 0 offset |
| Skew compensation | 62 ns |
| Maximum resolution | |
| MTP 1500RL 15HD A SEQ | Up to 1600x1200 and 1080p at 1500'
Up to 1920x1200 and 2048x1080 at 1200' |
| All other models | Up to 1920x1200 or 2048x1080 or 1080p at 300'
Up to 1024x768 at 600' |
| NOTE | See the user guide for the maximum distances recommended for specific resolutions. |
|
|
| Sync |
|---|
| Input type (transmitters) | RGBHV, RGBS, RGsB, RsGsBs |
| Output type (receivers) | RGBHV, RGBS, RGsB, RsGsBs |
| Standards | NTSC 3.58, NTSC 4.43, PAL, SECAM |
| Input level (transmitter) | 3.5 V to 5.5 Vp-p, unterminated |
| Output level (receivers) | 4.0 V to 5.0 Vp-p, unterminated |
| Input impedance (transmitter) | 573 ohms ±5% |
| Output impedance (receivers) | |
| MTP C7 15HD models | 92 ohms ±8% (25 mA) |
| All other models | 110 ohms |
| Polarity | |
| Transmitter | Positive or negative (follows input polarity) |
| Receivers | Positive or negative (switch-selectable) |
|
| Audio — all models |
|---|
| Number/signal type | 1 set of proprietary analog signals |
| Connectors | 1 female RJ-45 |
| Gain | Unbalanced output: 0 dB; balanced output: +6 dB |
| Frequency response | 20 Hz to 20 kHz, ±1 dB |
| THD + Noise | 0.15% @ 1 kHz, 0.3% @ 20 kHz at nominal level |
| S/N | >70 dB at maximum output (unweighted) |
| Stereo channel separation | >60 dB @ 1 kHz |
| CMRR | >43 dB @ 20 Hz to 20 kHz |
|
| Audio input — transmitters |
|---|
| Number/signal type | 1 stereo, unbalanced |
| Connectors | (1) 3.5 mm mini stereo jack |
| Impedance | >10k ohms, unbalanced |
| Nominal level | +4 dBu (1.23 Vrms), -10 dBV
(316 mVrms) |
| Maximum level | |
| MTP C7 15HD models | +12 dBu, (unbalanced) at 1%THD+N |
| All other models | +18 dBu, (unbalanced) at 1%THD+N |
| NOTE | 0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu |
|
|
| Audio output — MTP T 15HD A AAP, MTP T 15HD A D, MTP T 15HD A WM local stereo output |
|---|
| Number/signal type | 1 stereo, balanced/unbalanced |
| Connectors | (1) 3.5 mm direct insertion captive screw connector, 5 pole |
| Impedance | 50 ohms unbalanced, 100 ohms balanced |
| Gain error | ±1 dB channel to channel |
| Maximum level (Hi-Z) | >+23 dBu, balanced or unbalanced at 1% THD+N |
| Maximum level (600 ohm) | >+17 dBm, balanced or unbalanced at 1% THD+N |
|
| Audio output — receivers |
|---|
| Number/signal type | |
| MTP R 15HD RSA D | 1 mono, balanced/unbalanced |
| All other receivers | 2 mono, balanced/unbalanced |
| Connectors | |
| MTP R 15HD RSA D | (1) 3.5 mm captive screw connector, 5 pole (uses 3 poles) |
| All other receivers | (1) 3.5 mm captive screw connector, 5 pole |
| Impedance | 50 ohms unbalanced, 100 ohms balanced |
| Gain error | ±1 dB channel to channel |
| Nominal level | +4 dBu (1.23 Vrms), -10 dBV (316 mVrms) |
| Maximum level | |
| MTP R 15HD RSA D | 14 dBm, unbalanced at 1% THD+N |
| All other receivers | +18 dBu, unbalanced at 1% THD+N |
|
| Control/remote — external device (pass-through, unidirectional or bidirectional) — MTP R 15HD RSA D only |
|---|
| Serial control port input/output | 1 set of proprietary signals on a female RJ-45 jack |
| Serial control port output/input | RS-232 via 3 poles of a 3.5 mm captive screw connector, 5 pole |
| Baud rates | Up to 38400 bps at up to 600' (182.9 m) (Higher data rates and distances are possible. Performance varies based on baud rate and cable length.) |
| Protocol | Data bits = 5 - 8
Stop bits = 1 or 2
Parity = odd, even, none
Flow control = XON, XOFF, none |
| NOTE | Protocol is mirrored between the transmitter and the receiver. |
|
| Serial control pin configuration | Captive screw connector: 1 = Tx, 2 = Rx,
3 = GND |
|
| General |
|---|
| Recommended cable type | |
| Models other than C7 models | CAT 5/5e/6 (shielded or unshielded) |
| Required cable type | |
| MTP C7 15HD models | Extron STP201 or CAT 7 |
| Power supply | External
Input: 100-240 VAC, 50-60 Hz
Output: 12 VDC, 1 A, 12 watts |
| Power input requirements | |
| MTP 1500RL 15HD A SEQ | 12 VDC, 1 A |
| All other models | 12 VDC, 0.5 A |
| Ambient temperature/humidity | Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing |
| Cooling | |
| MTP 1500RL 15HD A SEQ | Convection, vents sides to top |
| All other models | Convection, no vents |
| Mounting | |
| Rack mount | |
| MTP T 15HD A, MTP RL 15HD A, MTP RL 15HD A SEQ, MTP 1500RL 15HD A SEQ | Yes, with optional 1U rack shelf |
| Furniture or wall mount | |
| MTP T 15HD A, MTP RL 15HD A, MTP RL 15HD A SEQ | Yes, with optional under-desk mounting kit |
| MTP T 15HD A AAP | Yes, with optional AAP mounting faceplates that have double space high AAP opening |
| MTP T 15HD A D, MTP R 15HD RSA D | Yes, in a decorator-style opening with a standard electrical wall box or decorator-style size mud ring |
| MTP T 15HD A WM | Yes, in a 1-gang opening |
| Wall mount | |
| MTP 1500RL 15HD models | Yes, with optional wall mounting kit |
| Pole mount | |
| MTP T 15HD A, MTP RL 15HD A, MTP RL 15HD A SEQ | Yes, with optional pole mounting kit |
| Enclosure type | Metal |
| Enclosure dimensions | |
| MTP T 15HD A, MTP RL 15HD A, MTP RL 15HD A SEQ | 1.7" H x 4.3" W x 3.0" D (1U high, quarter rack wide)
4.3 cm H x 10.9 cm W x 7.6 cm D
(Depth excludes connectors.) |
| MTP C7 15HD models | 1.7" H x 4.3" W x 3.0" D (1U high, quarter rack wide)
(4.3 cm H x 10.9 cm W x 7.6 cm D)
(Depth excludes connectors and knobs.) |
| MTP 1500RL 15HD SEQ models | 1.0" H x 8.75" W x 6.0" D (half rack wide)
(2.5 cm H x 22.2 cm W x 15.2 cm D)
(Depth excludes connectors.) |
| Faceplates | |
| MTP T 15HD A AAP | 1.4" H x 3.5" W x 0.1" D (3.6 cm H x 8.9 cm W x 0.3 cm D)
(double space high AAP plate) |
| MTP T 15HD A D, MTP R 15HD RSA D | 2.6" H* x 1.3" W x 0.1" D (6.6 cm H* x 3.3 cm W x 0.3 cm D)
(Fits the opening in a 1 gang, 4.4" H x 2.7" W
decorator-style wallplate. Depth excludes connectors.)
*Overall height is 4.1" (10.4 cm) including mounting tabs. |
| MTP T 15HD A WM | 4.5" H x 2.8" W x 0.1" D
(11.4 cm H x 7.1 cm W x 0.3 cm D)
(1 gang) |
| Device | |
| MTP R 15HD RSA D | 2.75" H x 1.65" W x 1.3" D
(7.0 cm H x 4.2 cm W x 3.3 cm D)
(Depth excludes connectors.) |
| Other AAP, D, and WM models | 2.7" H x 1.4" W x 1.4" D
(6.9 cm H x 3.6 cm W x 3.6 cm D)
(Depth excludes connectors.) |
| Product weight | |
| MTP 1500RL 15HD A SEQ | 1 lb (0.5 kg) |
| All other models | 0.4 lbs (0.2 kg) |
| Vibration | ISTA 1A in carton (International Safe Transit Association) |
| Regulatory compliance | |
| Safety | CE, c-UL, UL |
| EMI/EMC | CE, C-tick, FCC Class A, ICES, VCCI |
| Product warranty | 3 years parts and labor |
| Everlast power supply warranty | 7 years parts and labor |
| NOTE | All nominal levels are at ±10%. |
|
| NOTE | Specifications are subject to change without notice. |
|
| (CMS-041917-D18) |