| PowerCage™ 1600 with PowerCage MTP Boards |
|
| Video — PowerCage MTP T 15HD RSA, PowerCage MTP R 15HD RSA SEQ |
|---|
| Gain | Unity |
| Number/signal type | 1 set of proprietary analog signals |
| Connector | 1 female RJ-45 |
|
| Video input — PowerCage MTP T 15HD RSA |
|---|
| Number/signal type | 1 analog RGBHV, RGBS, RGsB, RsGsBs, component video (YUVi or YUVp/HDTV), S-video, or composite video |
| Connector | 1 female 15-pin HD |
| Nominal levels | 1 Vp-p for Y of component video and S-video, and for composite video
0.7 Vp-p for RGB and for R-Y and B-Y of component video
0.3 Vp-p for C of S-video |
| Minimum/maximum levels | 0.3 V to 1.45 Vp-p |
| Impedance | 75 ohms |
| Horizontal frequency | 15 kHz to 130 kHz |
| Vertical frequency | 30 Hz to 150 Hz |
| Return loss | >30 dB @ 5 MHz |
| DC offset (max. allowable) | 250 mV |
|
| Video output — PowerCage MTP R 15HD RSA SEQ |
|---|
| Number/signal type | 1 analog VGA-UXGA RGBHV, RGBS, RGsB, RsGsBs, component video (YUVi or YUVp/HDTV), S-video, or composite video |
| Connector | 1 female 15-pin HD |
| Nominal levels | 1 Vp-p for Y of component video and S-video, and for composite video
0.7 Vp-p for RGB and for R-Y and B-Y of component video
0.3 Vp-p for C of S-video |
| Minimum/maximum levels | 0.3 V to 1.45 Vp-p |
| Impedance | 75 ohms |
| Return loss | >30 dB @ 5 MHz |
| DC offset | <±0.35 mV with input at 0 offset |
| Skew compensation | 62 ns |
| Maximum resolution | Up to 1920x1200 or 2048x1080 or 1080p at 300'
Up to 1024x768 at 600' |
| NOTE | See the user guide for the maximum distances recommended for specific resolutions. |
|
|
| Sync — PowerCage MTP T 15HD RSA, PowerCage MTP R 15HD RSA SEQ |
|---|
| Input/output type | RGBHV, RGBS, RGsB, RsGsBs |
| Standards | NTSC 3.58, NTSC 4.43, PAL, SECAM |
| Input level (transmitter) | 3.5 V to 5.5 Vp-p, unterminated |
| Output level (receiver) | 4.0 V to 5.0 Vp-p, unterminated |
| Input impedance (transmitter) | 573 ohms ±5% |
| Output impedance (receiver) | 110 ohms |
| Polarity | |
| Transmitter | Positive or negative (follows input polarity) |
| Receiver | Positive or negative (switch-selectable) |
|
| Video — PowerCage MTP T AV, PowerCage MTP R AV |
|---|
| Gain | Unity |
| Differential phase error | <1.0° at 3.58 MHz and 4.43 MHz |
| Differential gain error | <1.0% at 3.58 MHz and 4.43 MHz |
|
| Video input — PowerCage MTP T AV |
|---|
| Number/signal type | 1 S-video or composite video |
| Connectors | 2 female BNC |
| Nominal level | 1 Vp-p for Y of S-video and for composite video
0.3 Vp-p for C of S-video |
| Minimum/maximum levels | 0.3 V to 1.5 Vp-p with no offset |
| Impedance | 75 ohms |
| Return loss | >30 dB, DC @ 10 MHz |
| DC offset (max. allowable) | 250 mV |
|
| Video output — PowerCage MTP R AV |
|---|
| Number/signal type | 1 S-video or composite video |
| Connectors | 2 female BNC |
| Nominal level | 1 V p-p for Y of S-video and for composite video
0.3 V p-p for C of S-video |
| Minimum/maximum levels | 0.3 V to 1.5 Vp-p |
| Impedance | 75 ohms |
| Return loss | >35 dB @ 5 MHz |
| DC offset | ±20 mV with input at 0 offset |
|
| Sync — PowerCage MTP T AV, PowerCage MTP R AV |
|---|
| Standards | NTSC 3.58, NTSC 4.43, PAL, SECAM |
|
| Audio — PowerCage MTP T 15HD RSA, PowerCage MTP R 15HD RSA SEQ, PowerCage MTP T AV, PowerCage MTP R AV |
|---|
| Number/signal type | 1 set of proprietary analog signals |
| Connector | 1 female RJ-45 |
| Gain | Unbalanced output: 0 dB; balanced output: +6 dB |
| Frequency response | 20 Hz to 20 kHz, ±1 dB |
| THD + Noise | 0.15% @ 1 kHz, 0.3% @ 20 kHz at nominal level |
| S/N | >70 dB at maximum output (unweighted) |
| Stereo channel separation | >60 dB @ 1 kHz |
| CMRR | >43 dB @ 20 Hz to 20 kHz |
|
| Audio input — PowerCage MTP T 15HD RSA, PowerCage MTP T AV |
|---|
| Number/signal type | |
| PowerCage MTP T 15HD RSA | 1 stereo, unbalanced |
| PowerCage MTP T AV | 1 stereo, balanced/unbalanced |
| Connector | (1) 3.5 mm captive screw connector, 5 pole |
| Impedance | |
| PowerCage MTP T 15HD RSA | >10k ohms, unbalanced |
| PowerCage MTP T AV | >10k ohms, unbalanced; >20k ohms, balanced; AC coupled |
| Nominal levels | +4 dBu (1.23 Vrms), -10 dBV (316 mVrms) |
| Maximum level | +18 dBu, (unbalanced) at 1% THD+N |
| NOTE | 0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu |
|
|
| Audio output — PowerCage MTP R 15HD RSA SEQ, PowerCage MTP R AV |
|---|
| Number/signal type | |
| PowerCage MTP R 15HD RSA SEQ | 1 mono, balanced/unbalanced |
| PowerCage MTP R AV | 2 mono, balanced/unbalanced |
| Connector | (1) 3.5 mm captive screw connector, 5 pole |
| Impedance | 50 ohms unbalanced, 100 ohms balanced |
| Gain error | ±1 dB channel to channel |
| Nominal levels | +4 dBu (1.23 Vrms), -10 dBV (316 mVrms) |
| Maximum level | +18 dBu, unbalanced at 1% THD+N |
|
| Control/remote |
|---|
| NOTE | PowerCage MTP AV Series boards do not have any RS-232 communication.
PowerCage MTP 15HD Series boards have only pass-through RS-232 communication. |
|
| Serial control ports | |
| Enclosure | 1 bidirectional RS-232, 2.5 mm mini stereo jack (front panel) |
| PowerCage MTP 15HD boards | External device, pass-through, uni- or bidirectional
Input/output: 1 set of proprietary signals on a female RJ-45 jack
Output/input: 1 RS-232 via 3 poles of a 3.5 mm captive screw connector (3 pole for transmitter, 5 pole for receiver) |
| Baud rate and protocol | |
| PowerCage MTP 15HD boards | |
| Baud rates | Up to 38400 bps at up to 600' (182.9 m)
(Higher data rates and distances are possible. Performance varies based on baud rate and cable length.) |
| Protocol | Data bits = 5 - 8
Stop bits = 1 or 2
Parity = odd, even, none
Flow control = XON, XOFF, none
Defaults: 8 data bits, 1 stop bit, no parity |
| NOTE | For PowerCage MTP 15HD boards, protocol is mirrored between the transmitter and the receiver. |
|
| Serial control pin configurations |
| Captive screw connector | |
| PowerCage MTP 15HD boards | Transmitter: 1 = Tx, 2 = Rx, 3 = GND
Receiver: 3 = GND, 4 = Tx, 5 = Rx |
| Mini stereo jack | RS-232: tip = Tx, ring = Rx, sleeve = GND |
|
| General |
|---|
| Recommended cable type | Extron Enhanced Skew-Free™ AV UTP cable or CAT 5/5e/6 (shielded or unshielded) |
| Power supply | Internal, 1 or 2* (positive-negative), primary and redundant, hot-swappable
100-240 VAC, 50-60 Hz
*A redundant power supply is optional. |
| Power consumption | |
| System | Enclosure without boards: 12.4 watts |
| Individual MTP boards | MTP T 15HD RSA: 4.30 watts
MTP R 15HD RSA SEQ: 8.38 watts
MTP T AV: 2.69 watts
MTP R AV: 3.92 watts |
| Power input requirements for boards | 12 VDC, 1.0 A, supplied by the PowerCage enclosure |
| Ambient temperature/humidity | Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing |
| Cooling | Enclosure: fans, front to back
Boards: convection, within the PowerCage enclosure |
| Thermal dissipation | 27.6 BTU/hr |
| Mounting — PowerCage enclosure | |
| Rack mount | Yes |
| Enclosure type | Metal |
| Enclosure dimensions | |
| PowerCage enclosure | 5.25" H x 17.0" W x 12.25" D (3U high, full rack wide)
13.3 cm H x 43.2 cm W x 31.2 cm D
(Depth excludes connectors on the optional boards. Width excludes rack ears.) |
| PowerCage MTP R 15HD RSA SEQ | Fits a double slot opening in a PowerCage enclosure. |
| All other boards | Fits a single slot opening in a PowerCage enclosure. |
| Product weight | |
| PowerCage enclosure | 11.6 lbs (5.3 kg) |
| PowerCage MTP R 15HD RSA SEQ | 1.0 lbs (0.5 kg) |
| All other boards | 0.8 lbs (0.4 kg) |
| Shipping weight | |
| PowerCage enclosure | 13 lbs (6 kg) |
| Boards | 2 lbs (1 kg) each |
| Vibration | ISTA 1A in carton (International Safe Transit Association) |
| Regulatory compliance | |
| Safety | CE, c-UL, UL |
| EMI/EMC | CE, C-tick, FCC Class A, ICES, VCCI |
| Environmental | Complies with the appropriate requirements of RoHS, WEEE. |
| Product warranty | 3 years parts and labor |
| NOTE | All nominal levels are at ±10%. |
|
| NOTE | Specifications are subject to change without notice. |
|
| (8.0-051412-D7) |