| VTG 400D, VTG 400DVI |
|
| Video signal characteristics |
|---|
| Dot clock | 200 MHz (max.) |
| Pixel clock accuracy | 100 ppm |
| Horizontal frequency range (factory defaults) | 15 kHz to 131 kHz |
| Vertical frequency range (factory defaults) | 20 Hz to 120 Hz |
| Rise/fall time | |
| NTSC, PAL | 140 ns |
| All other signal rates | <4 ns |
|
| Video output |
|---|
| Number/signal type | 2 RGBHV, RGBS, RGsB, RsGsBs
1 component video
1 S-video
1 composite video (NTSC/PAL)
1 HD-SDI (SMPTE 292M), SDI (SMPTE 259M-C) – VTG 400D only
1 DVI-D (single link) – VTG 400DVI only |
| Connectors | 1 x 5 female BNC (RGB)
1 female 15-pin HD (RGB)
1 x 3 female BNC (component video)
1 female 4-pin mini DIN (S-video)
1 female BNC (composite video)
1 female BNC (SDI/HD-SDI) – VTG 400D only
1 female DVI-I (DVI-D) – VTG 400DVI only |
| Nominal level | 1 Vp-p for RsGsBs, Y of component video and S-video, and for composite video
0.7 Vp-p for RGB and for R-Y and B-Y of component video
0.286 Vp-p (burst) for C of NTSC S-video, 0.300 Vp-p (burst) for C of PAL S-video |
| Minimum/maximum levels | 0.0 V to 1.0 Vp-p |
| Impedance | 75 ohms |
| Resolutions | Computer (VGA–QXGA), video (NTSC, PAL), HDTV, 16:9 high resolutions, and custom resolutions (user-defined) |
| Return loss | -30 dB @ 5 MHz |
| DC offset | 0 ±5 mV for RGB and component video,
0 ±5 mV for NTSC S-video and composite video
14 mV ±5 mV for PAL S-video and composite video |
|
| Sync |
|---|
| Output type | RGBHV, RGBS, RGsB, RsGsBs (for RGB signals)
Tri-level on Y, R-Y, B-Y channels (component video 720p, 1080i, 1080p)
Bi-level on Y channel (for all other component video rates) |
| Standards | NTSC, PAL, SMPTE 170M, SMPTE 274M, SMPTE 293M, SMPTE 295M, SMPTE 296M |
| Output level | 0.3 Vp-p for RGsB, RsGsBs, component video (bi-level sync)
0.6 Vp-p for RsGsBs, component video (tri-level sync)
TTL: 5.0 Vp-p, unterminated for RGBHV, RGBS |
| Output impedance | 75 ohms |
| Max. rise/fall time | 5 ns (TTL sync) |
| Polarity | Positive or negative (scan rate/signal dependent) |
| Scope trigger connectors | 1 BNC female (scope trigger) |
|
| Audio |
|---|
| THD + Noise | <0.008% typical @ +6 dBu (1.55 V), 1 kHz
0.18% @ -38 dBu (9.75 mV), 20 Hz to 20 kHz |
| Flatness | ±0.05 dB @ 20 Hz to 20 kHz |
| Accuracy | ±0.4 dB |
| NOTE | 0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV≈ 2 dBu |
|
|
| Audio output |
|---|
| Number/signal type | |
| VTG 400D | 1 mono, balanced; 2 mono, unbalanced |
| VTG 400DVI | 1 mono, balanced; 1 mono, unbalanced |
| Connectors | |
| VTG 400D | (1) 3.5 mm mini stereo jack (unbalanced mono left and right, tip-ring-sleeve)
1 female RCA jack (unbalanced, tip-ring)
1 male 3-pin XLR (balanced) (pin 1 = GND, pin 2 = +, pin 3 = -) |
| VTG 400DVI | (1) 3.5 mm mini stereo jack (unbalanced mono left and right, tip-ring-sleeve)
1 male 3-pin XLR (balanced) (pin 1 = GND, pin 2 = +, pin 3 = -) |
| NOTE | The XLR output is immune to phantom power. |
|
| Impedance | 50 ohms unbalanced, 100 ohms balanced |
| Waveforms | Pink noise, white noise, sine wave (fixed/swept burst), square wave, polarity test |
| Level ranges | Pink noise: -72 dBu to -4 dBu (-74 dBV to -6 dBV) (0.20 mV to 500 mVrms)
Polarity test: -72 dBu to -14 dBu (-74 dBV to -16 dBV) (0.20 mV to 158 mVrms)
All other signal types: -72 dBu to +6 dBu (-74 dBV to +4 dBV) (0.20 mVrms to 1.58 Vrms) |
| Maximum level (Hi-Z) | >+6 dBu, balanced or unbalanced at 1% THD+N |
| Maximum level (600 ohm) | >+4.66 dBu, balanced or unbalanced at 1% THD+N |
| Crest factor (pink noise) | 3.25 (10.24 dB) |
| Crest factor (white noise) | 1.98 (5.95 dB) |
| Rise time (square wave) | 1.5 ms at 20 Hz to 7 µs at 5 kHz |
| Rise time (polarity test) | 5 µs |
| Frequency accuracy (sine wave) | 50 ppm |
|
| Control/remote — test generator |
|---|
| Serial control port | RS-232, 9-pin female D connector |
| Baud rate and protocol | 9600 baud, 8 data bits, 1 stop bit, no parity |
| Serial control pin configurations | 2 = Tx, 3 = Rx, 5 = GND |
| Program control | Extron's control/configuration program for Windows®
Extron's Simple Instruction Set (SIS™) |
|
| General |
|---|
| Power | 100 VAC to 240 VAC, 50-60 Hz, 15 watts, internal |
| Ambient temperature/humidity | Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing |
| Cooling | Convection, vents on sides |
| Rack mount | No |
| Enclosure type | Metal |
| Enclosure dimensions | 6.75" H x 9.0" W x 1.75" D
17.1 cm H x 22.9 cm W x 4.4 cm D
(7.5" [19.1 cm] H including connectors.) |
| Product weight | 3.3 lbs (1.5 kg) |
| Shipping weight | 7 lbs (4 kg) |
| Vibration | ISTA 1A in carton (International Safe Transit Association) |
| Regulatory compliance | |
| Safety | CE, c-UL, UL |
| EMI/EMC | CE, C-tick, FCC Class A, ICES, VCCI |
| Product warranty | 3 years parts and labor |
| NOTE | All nominal levels are at ±5%. |
|
| NOTE | Specifications are subject to change without notice. |
|
| (7.6-041409-D12) |