Página principal de Productos
Altavoces
Altavoces de montaje en superficie
Altavoces de columna Altavoces de techo Flat Field Altavoces de techo Altavoces colgantes Montaje y accesorios de altavoces Altavoces PoE Subwoofers
SM 26
Kit de montaje en superficie Montaje con articulación SM 26 SM 28 SM 3 SMK P SM 26/28 V-Lock

Twitter Copy Link

Imprimir

Profesional

SM 26

Altavoces de dos vías con woofer de 165 mm (6.5 in) de montaje en superficie SpeedMount

Características principales

Sistema de montaje oculto y patentado
Incluye placa de montaje de 0° y adaptador de montaje de 10°
Diseñado para utilizarse en instalaciones con reparto de tareas y recortar gastos
Woofer de largo alcance de 165 mm (6.5 in) con puertos duales de reflexión de graves ajustado
Tweeter con cúpula de seda de 25 mm (1 in)
Dos versiones disponibles para sistemas de baja impedancia o 70/100 V:
- Solo funcionamiento a 8 Ω directos
- Funcionamiento a 8 Ω directos y 70/100 V
Todas las características

Parte trasera y lateral de SM 26 y placa de montaje de 0º; y lateral de SM 26 con placa de montaje de 0º y adaptador de montaje de 10º

SM 26 con montaje con articulación (Yoke Mount) opcional

Previous Next

Galería de imágenes

Visión general interactiva

AutoDesk Revit

Selector de altavoces

Descripciones para consultores

Casos de éxito

Calculador de altavoces

Altavoces vendidos por parejas

Visión global
Vídeo
Descripción
Especificaciones
Diagrama
Ilustraciones
Descargas

Visión global

El altavoz de montaje en superficie SpeedMount^® SM 26 de Extron es un altavoz de dos vías con un sistema de montaje en pared oculto y patentado. Dispone de un woofer de 165 mm (6.5 in) con puertos duales ajustados y un tweeter de 25 mm (1 in). Además, proporciona un amplio rango de frecuencia, desde 65 Hz a 19,2 kHz, y una tasa de potencia de 60 W de ruido rosa continuo y 120 W de capacidad de programa continuo. El sistema de montaje exclusivo de Extron está diseñado para utilizarse en instalaciones con reparto de tareas y recortar gastos. Este altavoz está disponible en un modelo de 8 Ω y una versión SM 26T que funciona tanto en modo de 8 Ω directos como 70 V y 100 V. El SM 26T dispone de un selector de potencia de seis posiciones, con un acceso práctico a través de la rejilla desde fuera del altavoz.

Vídeo

Descripción

Especificaciones

Diagrama

Ilustraciones

Descargas

Productos vistos recientemente

SM 26

FOX3 T 321

SM 26

Descripciones para consultores

Seleccione un número de referencia:

Select a Part Number:

Copiar el texto Copiado Se ha producido un error. Inténtelo de nuevo más tarde.

SM 26

Provide a two-way, 8 ohm surface mount speaker that shall accommodate division-of-labor installations.
1. Two-way surface mount speaker with a dual-ported enclosure, grille, crossover network, 8 ohm nominal impedance, and a concealed, lockable mounting system
  1. Driver Requirements
    1. Shall consist of a 6.5" (16.5 cm) polypropylene woofer
    2. Shall consist of a 1" (2.5 cm) silk dome tweeter
  2. Performance Requirements
    1. Shall provide a frequency range of 70 Hz to 18 kHz, -10 dB below average SPL, measured on-axis in full space
    2. Shall provide a power capacity of 60 watts (rms) continuous pink noise per IEC 60268-5 and 120 watts (rms) continuous program
    3. Shall provide a nominal sensitivity of 87 dB SPL (1 W, 1 m) measured in full space
    4. Shall provide a nominal impedance of 8 ohms
    5. Shall provide a crossover frequency of 2.5 kHz
  3. Electrical Requirements
    1. Shall support 8 ohm direct connection from power amplifiers
    2. Shall provide an internal overload protection circuit
    3. Shall support one incoming and one outgoing speaker level signal on one 4-pole, 10 mm Euro-style captive screw terminal block built into 0° mounting plate
      1. Shall support direct wiring of speaker or support wiring of multiple speakers using loop-through wiring terminals
      2. Shall support a maximum wire gauge of 12 AWG per connection point for a single wire
      3. Shall support a maximum wire gauge of 16 AWG per connection point for two wires
  4. Enclosure Requirements
    1. Shall consist of a plastic, trapezoidal enclosure with molded grille and dual bass reflex ports
    2. Shall have a black or white finish
    3. Shall measure 12.98" (32.97 cm) in height when using 0° mounting plate
    4. Shall measure 8.45" (21.46 cm) in width when using 0° mounting plate
    5. Shall protrude 6.45" (16.38 cm) into environment from mounting surface when using 0° mounting plate
    6. Shall weigh 8.4 lbs (3.81 kg) per speaker when using 0° mounting plate
  5. Mounting Requirements
    1. Shall include a 0° mounting plate for vertical or horizontal flush-with-the-wall installation
      1. Shall support both enclosure mounting and electrical connection as speaker is placed on mount
      2. Shall support all incoming and pass-through wiring for speaker
      3. Shall have a black or white finish to match speaker
    2. Shall include a four-position 10° mounting adapter for vertical or horizontal speaker installation with 10° of tilt downward, upward, left, or right
      1. Shall have a black or white finish to match speaker
    3. Shall provide cable raceway access on 0° mounting plate and 10° mounting adapter for surface-mounted wiring
    4. Shall support 180° of speaker pivot in 10° detented steps with the use of optional Extron Yoke Mount Kit that is available in black or white finish
    5. Shall provide a hidden locking speaker release mechanism
  6. General Requirements
    1. Shall be sold in pairs
    2. Shall meet regulatory compliances
      1. Shall comply with appropriate requirements of RoHS and WEEE
    3. Shall provide five year parts and labor warranty
2. Approved device shall be the Extron SM 26, part number 60-1308-02 or 60-1308-03; no alternates or equals.

SM 26

Provide a two-way, 8 ohm surface mount speaker that shall accommodate division-of-labor installations.
1. Two-way surface mount speaker with a dual-ported enclosure, grille, crossover network, 8 ohm nominal impedance, and a concealed, lockable mounting system
  1. Driver Requirements
    1. Shall consist of a 6.5" (16.5 cm) polypropylene woofer
    2. Shall consist of a 1" (2.5 cm) silk dome tweeter
  2. Performance Requirements
    1. Shall provide a frequency range of 70 Hz to 18 kHz, -10 dB below average SPL, measured on-axis in full space
    2. Shall provide a power capacity of 60 watts (rms) continuous pink noise per IEC 60268-5 and 120 watts (rms) continuous program
    3. Shall provide a nominal sensitivity of 87 dB SPL (1 W, 1 m) measured in full space
    4. Shall provide a nominal impedance of 8 ohms
    5. Shall provide a crossover frequency of 2.5 kHz
  3. Electrical Requirements
    1. Shall support 8 ohm direct connection from power amplifiers
    2. Shall provide an internal overload protection circuit
    3. Shall support one incoming and one outgoing speaker level signal on one 4-pole, 10 mm Euro-style captive screw terminal block built into 0° mounting plate
      1. Shall support direct wiring of speaker or support wiring of multiple speakers using loop-through wiring terminals
      2. Shall support a maximum wire gauge of 12 AWG per connection point for a single wire
      3. Shall support a maximum wire gauge of 16 AWG per connection point for two wires
  4. Enclosure Requirements
    1. Shall consist of a plastic, trapezoidal enclosure with molded grille and dual bass reflex ports
    2. Shall have a black or white finish
    3. Shall measure 12.98" (32.97 cm) in height when using 0° mounting plate
    4. Shall measure 8.45" (21.46 cm) in width when using 0° mounting plate
    5. Shall protrude 6.45" (16.38 cm) into environment from mounting surface when using 0° mounting plate
    6. Shall weigh 8.4 lbs (3.81 kg) per speaker when using 0° mounting plate
  5. Mounting Requirements
    1. Shall include a 0° mounting plate for vertical or horizontal flush-with-the-wall installation
      1. Shall support both enclosure mounting and electrical connection as speaker is placed on mount
      2. Shall support all incoming and pass-through wiring for speaker
      3. Shall have a black or white finish to match speaker
    2. Shall include a four-position 10° mounting adapter for vertical or horizontal speaker installation with 10° of tilt downward, upward, left, or right
      1. Shall have a black or white finish to match speaker
    3. Shall provide cable raceway access on 0° mounting plate and 10° mounting adapter for surface-mounted wiring
    4. Shall support 180° of speaker pivot in 10° detented steps with the use of optional Extron Yoke Mount Kit that is available in black or white finish
    5. Shall provide a hidden locking speaker release mechanism
  6. General Requirements
    1. Shall be sold in pairs
    2. Shall meet regulatory compliances
      1. Shall comply with appropriate requirements of RoHS and WEEE
    3. Shall provide five year parts and labor warranty
2. Approved device shall be the Extron SM 26, part number 60-1308-02 or 60-1308-03; no alternates or equals.

SM 26

Provide a two-way, 8 ohm surface mount speaker that shall accommodate division-of-labor installations.
1. Two-way surface mount speaker with a dual-ported enclosure, grille, crossover network, 8 ohm nominal impedance, and a concealed, lockable mounting system
  1. Driver Requirements
    1. Shall consist of a 6.5" (16.5 cm) polypropylene woofer
    2. Shall consist of a 1" (2.5 cm) silk dome tweeter
  2. Performance Requirements
    1. Shall provide a frequency range of 70 Hz to 18 kHz, -10 dB below average SPL, measured on-axis in full space
    2. Shall provide a power capacity of 60 watts (rms) continuous pink noise per IEC 60268-5 and 120 watts (rms) continuous program
    3. Shall provide a nominal sensitivity of 87 dB SPL (1 W, 1 m) measured in full space
    4. Shall provide a nominal impedance of 8 ohms
    5. Shall provide a crossover frequency of 2.5 kHz
  3. Electrical Requirements
    1. Shall support 8 ohm direct connection from power amplifiers
    2. Shall provide an internal overload protection circuit
    3. Shall support one incoming and one outgoing speaker level signal on one 4-pole, 10 mm Euro-style captive screw terminal block built into 0° mounting plate
      1. Shall support direct wiring of speaker or support wiring of multiple speakers using loop-through wiring terminals
      2. Shall support a maximum wire gauge of 12 AWG per connection point for a single wire
      3. Shall support a maximum wire gauge of 16 AWG per connection point for two wires
  4. Enclosure Requirements
    1. Shall consist of a plastic, trapezoidal enclosure with molded grille and dual bass reflex ports
    2. Shall have a black or white finish
    3. Shall measure 12.98" (32.97 cm) in height when using 0° mounting plate
    4. Shall measure 8.45" (21.46 cm) in width when using 0° mounting plate
    5. Shall protrude 6.45" (16.38 cm) into environment from mounting surface when using 0° mounting plate
    6. Shall weigh 8.4 lbs (3.81 kg) per speaker when using 0° mounting plate
  5. Mounting Requirements
    1. Shall include a 0° mounting plate for vertical or horizontal flush-with-the-wall installation
      1. Shall support both enclosure mounting and electrical connection as speaker is placed on mount
      2. Shall support all incoming and pass-through wiring for speaker
      3. Shall have a black or white finish to match speaker
    2. Shall include a four-position 10° mounting adapter for vertical or horizontal speaker installation with 10° of tilt downward, upward, left, or right
      1. Shall have a black or white finish to match speaker
    3. Shall provide cable raceway access on 0° mounting plate and 10° mounting adapter for surface-mounted wiring
    4. Shall support 180° of speaker pivot in 10° detented steps with the use of optional Extron Yoke Mount Kit that is available in black or white finish
    5. Shall provide a hidden locking speaker release mechanism
  6. General Requirements
    1. Shall be sold in pairs
    2. Shall meet regulatory compliances
      1. Shall comply with appropriate requirements of RoHS and WEEE
    3. Shall provide five year parts and labor warranty
2. Approved device shall be the Extron SM 26, part number 60-1308-02 or 60-1308-03; no alternates or equals.

SM 26

Provide a two-way, 8 ohm surface mount speaker that shall accommodate division-of-labor installations.
1. Two-way surface mount speaker with a dual-ported enclosure, grille, crossover network, 8 ohm nominal impedance, and a concealed, lockable mounting system
  1. Driver Requirements
    1. Shall consist of a 6.5" (16.5 cm) polypropylene woofer
    2. Shall consist of a 1" (2.5 cm) silk dome tweeter
  2. Performance Requirements
    1. Shall provide a frequency range of 70 Hz to 18 kHz, -10 dB below average SPL, measured on-axis in full space
    2. Shall provide a power capacity of 60 watts (rms) continuous pink noise per IEC 60268-5 and 120 watts (rms) continuous program
    3. Shall provide a nominal sensitivity of 87 dB SPL (1 W, 1 m) measured in full space
    4. Shall provide a nominal impedance of 8 ohms
    5. Shall provide a crossover frequency of 2.5 kHz
  3. Electrical Requirements
    1. Shall support 8 ohm direct connection from power amplifiers
    2. Shall provide an internal overload protection circuit
    3. Shall support one incoming and one outgoing speaker level signal on one 4-pole, 10 mm Euro-style captive screw terminal block built into 0° mounting plate
      1. Shall support direct wiring of speaker or support wiring of multiple speakers using loop-through wiring terminals
      2. Shall support a maximum wire gauge of 12 AWG per connection point for a single wire
      3. Shall support a maximum wire gauge of 16 AWG per connection point for two wires
  4. Enclosure Requirements
    1. Shall consist of a plastic, trapezoidal enclosure with molded grille and dual bass reflex ports
    2. Shall have a black or white finish
    3. Shall measure 12.98" (32.97 cm) in height when using 0° mounting plate
    4. Shall measure 8.45" (21.46 cm) in width when using 0° mounting plate
    5. Shall protrude 6.45" (16.38 cm) into environment from mounting surface when using 0° mounting plate
    6. Shall weigh 8.4 lbs (3.81 kg) per speaker when using 0° mounting plate
  5. Mounting Requirements
    1. Shall include a 0° mounting plate for vertical or horizontal flush-with-the-wall installation
      1. Shall support both enclosure mounting and electrical connection as speaker is placed on mount
      2. Shall support all incoming and pass-through wiring for speaker
      3. Shall have a black or white finish to match speaker
    2. Shall include a four-position 10° mounting adapter for vertical or horizontal speaker installation with 10° of tilt downward, upward, left, or right
      1. Shall have a black or white finish to match speaker
    3. Shall provide cable raceway access on 0° mounting plate and 10° mounting adapter for surface-mounted wiring
    4. Shall support 180° of speaker pivot in 10° detented steps with the use of optional Extron Yoke Mount Kit that is available in black or white finish
    5. Shall provide a hidden locking speaker release mechanism
  6. General Requirements
    1. Shall be sold in pairs
    2. Shall meet regulatory compliances
      1. Shall comply with appropriate requirements of RoHS and WEEE
    3. Shall provide five year parts and labor warranty
2. Approved device shall be the Extron SM 26, part number 60-1308-02 or 60-1308-03; no alternates or equals.

SM 26T

Provide a two-way surface mount speaker that shall provide an internal transformer and accommodate division-of-labor installations.
1. Two-way surface mount speaker with dual-ported enclosure, grille, crossover network, internal transformer for 8 ohm direct and 70/100 volt operation, and a concealed, lockable mounting system
  1. Driver Requirements
    1. Shall consist of a 6.5" (16.5 cm) polypropylene woofer
    2. Shall consist of a 1" (2.5 cm) silk dome tweeter
  2. Performance Requirements
    1. Shall provide a frequency range of 70 Hz to 18 kHz, -10 dB below average SPL, measured on-axis in full space
    2. Shall provide a power capacity of 60 watts (rms) continuous pink noise per IEC 60268-5 and 120 watts (rms) continuous program
    3. Shall provide a nominal sensitivity of 87 dB SPL (1 W, 1 m) measured in full space
    4. Shall provide a nominal impedance of 8 ohms
    5. Shall provide a crossover frequency of 2.5 kHz
  3. Electrical Requirements
    1. Shall support 8 ohm direct or 70/100 volt connection from power amplifiers
    2. Shall provide a six-position, through-the-grille power tap selector
      1. Shall provide selectable rotary switch taps for 70 volt operation, including 32, 16, 8, 4, and 2 watts, and 8 ohms direct
      2. Shall provide selectable rotary switch taps for 100 volt operation, including 32, 16, 8, and 4 watts, and 8 ohms direct
      3. Shall provide speaker tap selector and selection guide on the front of the speaker
    3. Shall provide an internal overload protection circuit
    4. Shall support one incoming and one outgoing speaker level signal on one 4-pole, 10 mm Euro-style captive screw terminal block built into 0° mounting plate
      1. Shall support direct wiring of speaker or support wiring of multiple speakers using loop-through wiring terminals
      2. Shall support a maximum wire gauge of 12 AWG per connection point for a single wire
      3. Shall support a maximum wire gauge of 16 AWG per connection point for two wires
  4. Enclosure Requirements
    1. Shall consist of a plastic, trapezoidal enclosure with molded grille and dual bass reflex ports
    2. Shall have a black or white finish
    3. Shall measure 12.98" (32.97 cm) in height when using 0° mounting plate
    4. Shall measure 8.45" (21.46 cm) in width when using 0° mounting plate
    5. Shall protrude 6.45" (16.38 cm) into environment from mounting surface when using 0° mounting plate
    6. Shall weigh 9.7 lbs (4.40 kg) per speaker when using 0° mounting plate
  5. Mounting Requirements
    1. Shall include a 0° mounting plate for vertical or horizontal flush-with-the-wall enclosure installation
      1. Shall support both enclosure mounting and electrical connection as speaker is placed on mount
      2. Shall support all incoming and pass-through wiring for speaker
      3. Shall have a black or white finish to match speaker
    2. Shall include a four-position 10° mounting adapter for vertical or horizontal speaker installation with 10° of tilt downward, upward, left, or right
      1. Shall have a black or white finish to match speaker
    3. Shall provide cable raceway access on 0° mounting plate and 10° mounting adapter for surface-mounted wiring
    4. Shall support 180° of speaker pivot in 10° detented steps with the use of optional Extron Yoke Mount Kit that is available in black or white finish
    5. Shall provide a hidden locking speaker release mechanism
  6. General Requirements
    1. Shall be sold in pairs
    2. Shall meet regulatory compliances
      1. Shall comply with appropriate requirements of RoHS and WEEE
    3. Shall provide five year parts and labor warranty
2. Approved device shall be the Extron SM 26T, part number 60-1308-12 or 60-1308-13; no alternates or equals.

SM 26T

Provide a two-way surface mount speaker that shall provide an internal transformer and accommodate division-of-labor installations.
1. Two-way surface mount speaker with dual-ported enclosure, grille, crossover network, internal transformer for 8 ohm direct and 70/100 volt operation, and a concealed, lockable mounting system
  1. Driver Requirements
    1. Shall consist of a 6.5" (16.5 cm) polypropylene woofer
    2. Shall consist of a 1" (2.5 cm) silk dome tweeter
  2. Performance Requirements
    1. Shall provide a frequency range of 70 Hz to 18 kHz, -10 dB below average SPL, measured on-axis in full space
    2. Shall provide a power capacity of 60 watts (rms) continuous pink noise per IEC 60268-5 and 120 watts (rms) continuous program
    3. Shall provide a nominal sensitivity of 87 dB SPL (1 W, 1 m) measured in full space
    4. Shall provide a nominal impedance of 8 ohms
    5. Shall provide a crossover frequency of 2.5 kHz
  3. Electrical Requirements
    1. Shall support 8 ohm direct or 70/100 volt connection from power amplifiers
    2. Shall provide a six-position, through-the-grille power tap selector
      1. Shall provide selectable rotary switch taps for 70 volt operation, including 32, 16, 8, 4, and 2 watts, and 8 ohms direct
      2. Shall provide selectable rotary switch taps for 100 volt operation, including 32, 16, 8, and 4 watts, and 8 ohms direct
      3. Shall provide speaker tap selector and selection guide on the front of the speaker
    3. Shall provide an internal overload protection circuit
    4. Shall support one incoming and one outgoing speaker level signal on one 4-pole, 10 mm Euro-style captive screw terminal block built into 0° mounting plate
      1. Shall support direct wiring of speaker or support wiring of multiple speakers using loop-through wiring terminals
      2. Shall support a maximum wire gauge of 12 AWG per connection point for a single wire
      3. Shall support a maximum wire gauge of 16 AWG per connection point for two wires
  4. Enclosure Requirements
    1. Shall consist of a plastic, trapezoidal enclosure with molded grille and dual bass reflex ports
    2. Shall have a black or white finish
    3. Shall measure 12.98" (32.97 cm) in height when using 0° mounting plate
    4. Shall measure 8.45" (21.46 cm) in width when using 0° mounting plate
    5. Shall protrude 6.45" (16.38 cm) into environment from mounting surface when using 0° mounting plate
    6. Shall weigh 9.7 lbs (4.40 kg) per speaker when using 0° mounting plate
  5. Mounting Requirements
    1. Shall include a 0° mounting plate for vertical or horizontal flush-with-the-wall enclosure installation
      1. Shall support both enclosure mounting and electrical connection as speaker is placed on mount
      2. Shall support all incoming and pass-through wiring for speaker
      3. Shall have a black or white finish to match speaker
    2. Shall include a four-position 10° mounting adapter for vertical or horizontal speaker installation with 10° of tilt downward, upward, left, or right
      1. Shall have a black or white finish to match speaker
    3. Shall provide cable raceway access on 0° mounting plate and 10° mounting adapter for surface-mounted wiring
    4. Shall support 180° of speaker pivot in 10° detented steps with the use of optional Extron Yoke Mount Kit that is available in black or white finish
    5. Shall provide a hidden locking speaker release mechanism
  6. General Requirements
    1. Shall be sold in pairs
    2. Shall meet regulatory compliances
      1. Shall comply with appropriate requirements of RoHS and WEEE
    3. Shall provide five year parts and labor warranty
2. Approved device shall be the Extron SM 26T, part number 60-1308-12 or 60-1308-13; no alternates or equals.

SM 26T

Provide a two-way surface mount speaker that shall provide an internal transformer and accommodate division-of-labor installations.
1. Two-way surface mount speaker with dual-ported enclosure, grille, crossover network, internal transformer for 8 ohm direct and 70/100 volt operation, and a concealed, lockable mounting system
  1. Driver Requirements
    1. Shall consist of a 6.5" (16.5 cm) polypropylene woofer
    2. Shall consist of a 1" (2.5 cm) silk dome tweeter
  2. Performance Requirements
    1. Shall provide a frequency range of 70 Hz to 18 kHz, -10 dB below average SPL, measured on-axis in full space
    2. Shall provide a power capacity of 60 watts (rms) continuous pink noise per IEC 60268-5 and 120 watts (rms) continuous program
    3. Shall provide a nominal sensitivity of 87 dB SPL (1 W, 1 m) measured in full space
    4. Shall provide a nominal impedance of 8 ohms
    5. Shall provide a crossover frequency of 2.5 kHz
  3. Electrical Requirements
    1. Shall support 8 ohm direct or 70/100 volt connection from power amplifiers
    2. Shall provide a six-position, through-the-grille power tap selector
      1. Shall provide selectable rotary switch taps for 70 volt operation, including 32, 16, 8, 4, and 2 watts, and 8 ohms direct
      2. Shall provide selectable rotary switch taps for 100 volt operation, including 32, 16, 8, and 4 watts, and 8 ohms direct
      3. Shall provide speaker tap selector and selection guide on the front of the speaker
    3. Shall provide an internal overload protection circuit
    4. Shall support one incoming and one outgoing speaker level signal on one 4-pole, 10 mm Euro-style captive screw terminal block built into 0° mounting plate
      1. Shall support direct wiring of speaker or support wiring of multiple speakers using loop-through wiring terminals
      2. Shall support a maximum wire gauge of 12 AWG per connection point for a single wire
      3. Shall support a maximum wire gauge of 16 AWG per connection point for two wires
  4. Enclosure Requirements
    1. Shall consist of a plastic, trapezoidal enclosure with molded grille and dual bass reflex ports
    2. Shall have a black or white finish
    3. Shall measure 12.98" (32.97 cm) in height when using 0° mounting plate
    4. Shall measure 8.45" (21.46 cm) in width when using 0° mounting plate
    5. Shall protrude 6.45" (16.38 cm) into environment from mounting surface when using 0° mounting plate
    6. Shall weigh 9.7 lbs (4.40 kg) per speaker when using 0° mounting plate
  5. Mounting Requirements
    1. Shall include a 0° mounting plate for vertical or horizontal flush-with-the-wall enclosure installation
      1. Shall support both enclosure mounting and electrical connection as speaker is placed on mount
      2. Shall support all incoming and pass-through wiring for speaker
      3. Shall have a black or white finish to match speaker
    2. Shall include a four-position 10° mounting adapter for vertical or horizontal speaker installation with 10° of tilt downward, upward, left, or right
      1. Shall have a black or white finish to match speaker
    3. Shall provide cable raceway access on 0° mounting plate and 10° mounting adapter for surface-mounted wiring
    4. Shall support 180° of speaker pivot in 10° detented steps with the use of optional Extron Yoke Mount Kit that is available in black or white finish
    5. Shall provide a hidden locking speaker release mechanism
  6. General Requirements
    1. Shall be sold in pairs
    2. Shall meet regulatory compliances
      1. Shall comply with appropriate requirements of RoHS and WEEE
    3. Shall provide five year parts and labor warranty
2. Approved device shall be the Extron SM 26T, part number 60-1308-12 or 60-1308-13; no alternates or equals.

SM 26T

Provide a two-way surface mount speaker that shall provide an internal transformer and accommodate division-of-labor installations.
1. Two-way surface mount speaker with dual-ported enclosure, grille, crossover network, internal transformer for 8 ohm direct and 70/100 volt operation, and a concealed, lockable mounting system
  1. Driver Requirements
    1. Shall consist of a 6.5" (16.5 cm) polypropylene woofer
    2. Shall consist of a 1" (2.5 cm) silk dome tweeter
  2. Performance Requirements
    1. Shall provide a frequency range of 70 Hz to 18 kHz, -10 dB below average SPL, measured on-axis in full space
    2. Shall provide a power capacity of 60 watts (rms) continuous pink noise per IEC 60268-5 and 120 watts (rms) continuous program
    3. Shall provide a nominal sensitivity of 87 dB SPL (1 W, 1 m) measured in full space
    4. Shall provide a nominal impedance of 8 ohms
    5. Shall provide a crossover frequency of 2.5 kHz
  3. Electrical Requirements
    1. Shall support 8 ohm direct or 70/100 volt connection from power amplifiers
    2. Shall provide a six-position, through-the-grille power tap selector
      1. Shall provide selectable rotary switch taps for 70 volt operation, including 32, 16, 8, 4, and 2 watts, and 8 ohms direct
      2. Shall provide selectable rotary switch taps for 100 volt operation, including 32, 16, 8, and 4 watts, and 8 ohms direct
      3. Shall provide speaker tap selector and selection guide on the front of the speaker
    3. Shall provide an internal overload protection circuit
    4. Shall support one incoming and one outgoing speaker level signal on one 4-pole, 10 mm Euro-style captive screw terminal block built into 0° mounting plate
      1. Shall support direct wiring of speaker or support wiring of multiple speakers using loop-through wiring terminals
      2. Shall support a maximum wire gauge of 12 AWG per connection point for a single wire
      3. Shall support a maximum wire gauge of 16 AWG per connection point for two wires
  4. Enclosure Requirements
    1. Shall consist of a plastic, trapezoidal enclosure with molded grille and dual bass reflex ports
    2. Shall have a black or white finish
    3. Shall measure 12.98" (32.97 cm) in height when using 0° mounting plate
    4. Shall measure 8.45" (21.46 cm) in width when using 0° mounting plate
    5. Shall protrude 6.45" (16.38 cm) into environment from mounting surface when using 0° mounting plate
    6. Shall weigh 9.7 lbs (4.40 kg) per speaker when using 0° mounting plate
  5. Mounting Requirements
    1. Shall include a 0° mounting plate for vertical or horizontal flush-with-the-wall enclosure installation
      1. Shall support both enclosure mounting and electrical connection as speaker is placed on mount
      2. Shall support all incoming and pass-through wiring for speaker
      3. Shall have a black or white finish to match speaker
    2. Shall include a four-position 10° mounting adapter for vertical or horizontal speaker installation with 10° of tilt downward, upward, left, or right
      1. Shall have a black or white finish to match speaker
    3. Shall provide cable raceway access on 0° mounting plate and 10° mounting adapter for surface-mounted wiring
    4. Shall support 180° of speaker pivot in 10° detented steps with the use of optional Extron Yoke Mount Kit that is available in black or white finish
    5. Shall provide a hidden locking speaker release mechanism
  6. General Requirements
    1. Shall be sold in pairs
    2. Shall meet regulatory compliances
      1. Shall comply with appropriate requirements of RoHS and WEEE
    3. Shall provide five year parts and labor warranty
2. Approved device shall be the Extron SM 26T, part number 60-1308-12 or 60-1308-13; no alternates or equals.

Añadir un elemento al carro

Order Message Number

Referencia

Nota: Los productos de Extron que utilizan una salida de CA universal aceptan varios tipos de enchufes de CA. Antes de utilizarlo, asegúrese de que el dispositivo cumple con la normativa de su región y todos los estándares y reglamentos de seguridad local y electricidad.

Cant.

Total actual:

Ver carro

SM 26 -

Detalles del producto

Annotation Graphics Processor

To view this page ensure that Adobe Flash Player version 11.0.0 or greater is installed and enabled.

Compartir este artículo por correo electrónico

SM 26

Altavoces de dos vías con woofer de 165 mm (6.5 in) de montaje en superficie SpeedMount

Enviar a: *

Por favor, introduzca una dirección de correo electrónico válida.

Nota:

( caracteres restantes)

Recibir una copia

Gracias. Su correo electrónico ha sido enviado.

Error al enviar el correo electrónico. Por favor, inténtelo de nuevo más tarde.